700RB-II/1001RB-II Series
Front Panel Controls
Front Panel Controls
1-Balanced Direct Out:9-High Mid:
An electronically balanced output, that you can run to your P.A. system.Boost and cut at 1 kHz +6dB/ -10dB, ?Q Optimized,? band pass type. Works
2-Ground/Lift:on lower string harmonics, and effects the punch of your sound.
This switch disconnects the ground on the balanced, XLR output to eliminate10-Low Mid:
hum and buzz when connnecting to equipment that is running on a differentBoost and cut at 250Hz +6dB/-10dB, ?Q Optimized,? band pass type. Works
ground system.on the main body of your sound.
Pre/Post EQ Button:11-Bass:
Selects the direct out signal before or after the EQ.Boost and cut at 60Hz +10dB, shelving type. Controls low end push.
3-Direct Level Out12-Boost:
Controls the level at the direct out jack.A post EQ gain stage using GIVE technology which adds ?growl? as it is
4-Input:turned up.
A standard 1? input jack to plug in active or passive basses using a shielded13-Tweeter:
cord.Master volume control for the tweeter (50W) amp..
5- -14dB Pad:14-Tweeter Hi-Cut:
Input attenuator button. The button is generally left out, except in rare casesCuts frequencies above 10kHz, producing a more ?cone-like? (less metallic/
when the clip LED flashes. This switch should be pressed if the CLIP LED staysharsh) sound from the tweeter.
on continuously. It may be necessary to ?pad? the input if you are using a bass15-Woofer/Master:
with active electronics or very high output.Master volume control for the woofer (Main) amplifier.
Clip LED:16-Woofer Hi-Cut:
LED lights yellow when the input stage is being over-driven. If -14dBPress this button to engage the electronic crossover for the woofer. This cuts
PAD is pressed and clip LED still stays lit, turn down the volume onfrequencies above 5kHz (Rolls off the highs).
your bass.17-Effects Loop:
Tuning Mute Button:Send and return jacks provided for the insertion of effects after the EQ, but
Set this switch to ?On? when tuning up. No signal will be sent to the speakers,before the boost section. Some effect units have gain, turning the BOOST
or the P.A. system.down, will compensate for this.
Mute LED:18-Tuner Output
LED turns on when ?Tuning Mute? is switched to the ?ON? position.Output comes directly off the input stage and can be patched to a tuner with
6-Volume:a shielded patch cord. This output is unaffected by the Tuning Mute Feature.
Sets pre-amp gain after the input stage. It is used in conjunction with the input19-Power/Protect LED:
pad, to optimize the amplifier?s headroom.The LED is red at turn-on for five seconds while the amp powers up.
7-Voicing Filters:The LED turns blue when the amp is ready to play. Should the amp
4/5 String Bass:experience a fault (over heat, over current) the amp will mute and
Setting this button to the ?ON? position, voices the pre-amp for basses withthis LED will switch to red until the condition is corrected. This
?B? tuning (5 string bass). Leaving it in the ?Out? position will voice the ampLED turns off when the power switch is turned off.
like the 800RB, for a 4 string bass.20-Power Switch:
Contour:Turns the amplifier on or off. Should a problem occur during
Drops the mid-range frequencies while boosting lows & highs.operation press this switch out first. This turns the amp off, but
Presence:does not completely disconnect the power from the AC mains. The
Adds edge and definition to higher frequencies.power LED should be off at this point.
Active Equalization:
8-Treble:
Boost and cut at 7 kHz +14dB shelving type. Add or remove edge and
definition.
1111 |